photo ic for optical switch analog output photo ic for optical switch www.hamamatsu.com s11049 series 1 the s11049 series photo ics are designed for optical switches and provides an analog waveform output proportional to the intensity of incident pulsed light. features applications large allowable background light level: 4000 lx min. high linearity low noise: 1.8 mv rms max. optical switch optical receivers in various sensor devices absolute maximum ratings (ta=25 c) parameter symbol s11049-202sb s11049-203dt unit supply voltage vcc -0.5 to +7 v power dissipation * 1 p 250 300 mw output voltage vout -0.5 to +7 v operating temperature * 2 topr -25 to +85 c storage temperature * 2 tstg -40 to +100 -30 to +85 c * 1: power dissipation decreases at a rate of 3.3 mw/c on the s11049-202sb and 4 mw/c on the s11049-203dt at ta=25 c and above. * 2: no condensation note: exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. always be sure to use the product within the absolute maximum ratings.
photo ic for optical switch s11049 series 2 electrical and optical characteristics (ta=25 c, vcc=5.0 v) parameter symbol condition min. typ. max. unit supply voltage vcc 4.5 - 5.5 v current consumption icc - - 2.2 ma spectral response range - 380 to 1120 - nm peak sensitivity wavelength p - 760 - nm photo sensitivity a =950 nm * 3 input signal=100 khz including diffused re ection inside package 120 200 300 v/mw ac photoelectric sensitivity linearity alin input pulse signal 0.01 w to 4.0 w * 3 -10 - +10 % input pulse signal 4.0 w to 7.5 w * 3 -50 - +50 cut-off frequency * 4 low band fcl * 3 --50 khz high band fch 1250 1450 1650 allowable background light level * 5 pdc input pulse signal 2.5 w * 3 4000 6000 - lx output noise voltage (with no input) von * 3 - - 2.8 mv rms * 3: measurement circuit (waveform at terminal vo is measured.) * 5: this is de ned as the background light level in the active area at witch the photo ic sensitivity drops by 20% * 4: cutoff frequency de nition kpicc0161eb 5 v vo 0.1 f 0.01 f 5.1 k 3.3 k vcc out gnd block diagram spectral response (typical example) kpicc0162eb preamp buffer vcc out gnd photodiode wavelength (nm) relative sensitivity (%) 20 40 60 80 100 0 300 400 600 500 800 900 700 1000 1100 1200 (ta=25 c) kpicb0142eb frequency (logarithmic axis) output 3 db fcl fch kpicc0241ea
photo ic for optical switch s11049 series 3 dimensional outlines (unit: mm) tolerance unless otherwise noted: 0.1, 2 shaded area indicates burr. values in parentheses are not guaranteed, but for reference. lead surface finish: silver plating packing: polyethylene pack [anti-static type] (200 pcs/pack) gnd vout vcc gnd 2.5 0.2 5.0 1.0 2.0 5.0 16.5 1.0 (1.0) (0.8) 1.27 10 5 1.27 (specified at the lead root) 1.27 0.25 -0.1 +0.15 0.45 5.2 0.2 (including burr) 5.2 0.2 (including burr) 0.7 10 5 photosensitive area 1.1 0.8 ?1.2 depth 0.15 max. kpica0083ea s11049-202sb
photo ic for optical switch s11049 series 4 kpica0092ea s11049-203dt 0.8 0.8 0.8 0.05 0.45 0.75 1.3 0.8 3.4 mirror surface area 3.8 3.9 4.0 * 4.0 * 4.2 0.2 (including burr) (10 ) 0.4 3.2 0.2 (including burr) 2.4 mirror surface area 2.8 3.0 * 2.9 3.0 * 5.0 0.3 0.45 0.3 0.45 0.3 3.0 * 1.0 0.4 1.0 0.4 (10 ) 0.3 0.15 0.1 0.1 photosensitive area photosensitive surface photosensitive surface 0.8 1.1 (gnd) (gnd) gnd (gnd) vo vo (gnd) vcc (gnd) (gnd) connect the (gnd) terminal to the gnd terminal on the circuit board. tolerance unless otherwise noted: 0.1, 2 shaded area indicates burr. chip position accuracy with respect to package dimensions marked * x, y?0.2, ??2
photo ic for optical switch s11049 series 5 packing quantity 2000 pcs/reel packing type reel and desiccant in moisture-proof packaging (vacuum-sealed) standard packing specifications (s11049-203dt) kpicc0238eb 8.0 0.1 5.5 0.1 4.5 0.2 12.0 0.3 2.0 0.1 4.0 0.1 5.4 0.2 2.3 0.2 0.3 0.1 1.75 0.1 reel feed direction ?1.5 0.1 reel (conforms to jeita et-7200) embossed tape (unit: mm, material: ps, electrically conductive) dimensions hub diameter tape width material electrostatic characteristics 254 mm 100 mm 12 mm ps antistatic treatment
photo ic for optical switch s11049 series cat. no. kpic1087e01 aug. 2014 dn www.hamamatsu.com hamamatsu photonics k.k., solid state division 1126-1 ichino-cho, higashi-ku, hamamatsu city, 435-8558 japan, telephone: (81) 53-434-3311, fax: (81) 53-434-5184 u.s.a.: hamamatsu corporation: 360 foothill road, bridgewater, n.j. 08807, u.s.a., telephone: (1) 908-231-0960, fax: (1) 908-23 1-1218 germany: hamamatsu photonics deutschland gmbh: arzbergerstr. 10, d-82211 herrsching am ammersee, germany, telephone: (49) 8152-375-0, fax: (49) 8152-265-8 france: hamamatsu photonics france s.a.r.l.: 19, rue du saule trapu, parc du moulin de massy, 91882 massy cedex, france, telephone: 33-(1) 69 53 71 00, fax: 33-(1) 69 53 71 10 united kingdom: hamamatsu photonics uk limited: 2 howard court, 10 tewin road, welwyn garden city, hertfordshire al7 1bw, united kingdom, telephone: (44) 1707-294888, fax: (44) 1707-325777 north europe: hamamatsu photonics norden ab: torshamnsgatan 35 16440 kista, sweden, telephone: (46) 8-509-031-00, fax: (46) 8-5 09-031-01 italy: hamamatsu photonics italia s.r.l.: strada della moia, 1 int. 6, 20020 arese (milano), italy, telephone: (39) 02-93581733 , fax: (39) 02-93581741 china: hamamatsu photonics (china) co., ltd.: b1201, jiaming center, no.27 dongsanhuan beilu, chaoyang district, beijing 100020 , china, telephone: (86) 10-6586-6006, fax: (86) 10-6586-2866 product specifications are subject to change without prior notice due to improvements or other reasons. this document has been carefully prepared and the information contained is believed to be accurate. in rare cases, however, there may be inaccuracies such as text errors. before using these products, always contact us for the delivery specification sheet to check the latest specifications. type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(x)" which means preliminary specifications or a suffix "(z)" which means developmental specifications. the product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. however, even if within the warranty period we accept absolutely no liability for any loss caused by natural d isasters or improper product use. copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. information described in this material is current as of august, 2014. 6 time temperature 300 c 220 c 190 c 170 c preheating 70 to 90 s actual heating 40 s max. 240 c max. kpicb0171ea measured example of temperature profile with our hot-air reflow oven for product testing (s11049-203dt) a these products support lead-free soldering. after unpacking, store them in an environment at a temperature of 30 c or less and a humidity of 60% or less, and perform soldering within 24 hours. the effect that the product receives during reflow soldering varies depending on the circuit board and reflow oven that are use d. when setting the reflow soldering conditions, check for any problems by testing out the reflow soldering methods in advance. related information a notice metal, ceramic, plastic package products surface mount type products precautions www.hamamatsu.com/sp/ssd/doc_en.html
|
